Accuracy of photogrammetry and conventional impression techniques for complete-arch implant rehabilitation: an in vitro comparative study / 中华口腔医学杂志

Objective: To compare the accuracy of photogrammetry and conventional impression techniques for complete-arch implant rehabilitation. Methods: An edentulous maxillary stone cast containing 8 screw-retained implant abutment replicas was derived from a 74-year-old male patient who visited the Department of Dental Implant Center, Capital Medical University School of Stomatology in September 2019. The stone cast was copied through the open-tray splinted impression, and the copied cast was used as the master cast for this study. The abutment-level impressions of master cast were made by photogrammetry (PG) and the conventional impression technique (CNV) by one attending doctor. Group PG: after which scan bodies were connected to each implant replica, a photogrammetry system was used to obtain digital impressions of the master cast (n=10); Group CNV: conventional open-tray splinted impression technique was performed to fabricate conventional definitive casts (n=10). After connecting the scan bodies onto each implant replicas, the master cast and the 10 definitive casts from group CNV were digitized with a laboratory reference scanner. All data of group PG, group CNV and mater cast were saved as ".stl" files. For all test scans and reference scan, the three-dimensional information of scan bodies were converted to implant abutment replicas using a computer aided design software (Exocad). The data of the group PG and the group CNV were respectively registered with the reference data (trueness analysis) and pairwise within group (precision analysis) for accuracy evaluation in a three-dimensional analysis software (Geomagic Control X). Results: The trueness and precision of group PG [(17.33±0.34) and (2.50±0.79) μm ] were significantly statistically better than those of group CNV [(24.30±4.16) and (26.12±4.54) μm] respectively (t=-5.29 and -34.35, P<0.001). Conclusions: For complete-arch implant abutment-level impression, photogrammetry produces significantly better accuracy than conventional impression technique.

Application evaluation of prefabricated rigid connecting bar in implants immediate impression preparation of edentulous jaw / 北京大学学报(医学版)

OBJECTIVE@#To compare the operation complexity and accuracy of traditional splint impression technique and impression technique with prefabricated rigid connecting bar system for full-arch implants-supported fixed protheses in vitro.@*METHODS@#Standard mandibular edentulous model with six implant analogs was prepared. The implants were placed at the bone level and multiunit abutments screwed into the implants. Two impression techniques were performed: the traditional splint impression technique was used in the control group, and the rigid connecting bar system was used in the test group. In the control group, impression copings were screwed into the multiunit abutments and connected with autopolymerizing acrylic resin. Open tray impression was fabricated with custom tray and polyether. In the test group, cylinders were screwed into the multiunit abutments. Prefabricated rigid bars with suitable length were selected and connected to the cylinders with small amount of autopolymerizing acrylic resin, and open tray impression was obtained. Impression procedures were repeated 6 times in each group. The working time of the two impression methods were recorded and compared. Analogs were screws into the impressions and gypsum casts were poured. The gypsum casts and the standard model were transferred to stereolithography (STL) files with model scanner. Comparative analysis of the STL files of the gypsum casts and the standard model was carried out and the root mean square (RMS) error value of the gypsum casts of the control and test groups compared with the standard model was recorded. The trueness of the two impression techniques was compared.@*RESULTS@#The work time in the test group was significantly lower than that in the control group and the difference was statistically significant [(984.5±63.3) s vs. (1 478.3±156.2) s, P < 0.05]. Compared with the standard model, the RMS error value of the implant abutments in the test group was (16.9±5.5) μm. The RMS value in the control group was (20.2±8.0) μm. The difference between the two groups was not significant (P>0.05).@*CONCLUSION@#The prefabricated rigid connecting bar can save the chair-side work time in implants immediate loading of edentulous jaw and simplify the impression process. The impression accuracy is not significantly different from the traditional impression technology. The impression technique with prefabricated rigid connecting bar system is worthy of clinical application.

Extended-pour and conventional alginates: effect of storage time on dimensional accuracy and maintenance of details

ABSTRACT Objective: This study aimed to evaluate the dimensional stability and maintenance of details of conventional and high stability alginates up to 5-day storage. Methods: Two types of alginates were selected (n=10) for this study, conventional (Hydrogum) and high stability alginates (Hydrogum 5), which were produced with the aid of a cylindrical metal block and a ring-shaped metal mold (Specifications 18, 19, and 25, ANSI/ADA). Ten images were obtained from the molds for the dimensional stability test, which were taken immediately after their production and at each different storage periods (15 min, 24 h, 48 h, 72 h, 96 h, and 120 h) by a digital camera. The specimens were kept hermetically sealed in plastic bags (23°C) and then used to obtain 140 (n=70) dental stone models, used in the detail reproduction test, in which the angular accuracy of three grooves (20 µm, 50 µm, and 75 µm) was observed at each period. The details reproduction accuracy was classified using a predetermined score classification. Measurements of dimensional changes were made in the Corel DRAW X6 program. The data were submitted to the Student's t-test (α?#8197;= 0.05). Results: A statistically significant difference concerning the size of the matrix was observed after 24h for both alginates, and a statistically significant negative linear dimensional change (contraction) was verified after 24 h of storage (1.52% for the high stability alginate, and 1.32% for the conventional alginate). The high stability alginate kept the full details for 72 hours, while the conventional alginate, for 24 h. Both alginates reproduced the 75 µm groove at all storage periods. Conclusion: Impressions made with both alginates presented satisfactory clinical results when the alginates were immediately poured.

RESUMO Objetivo: O presente estudo teve como objetivo avaliar a estabilidade dimensional e manutenção de detalhes de alginatos convencionais e de alta estabilidade por até 5 dias de armazenamento. Métodos: Para esse estudo, foram selecionados dois tipos de alginatos: convencional (Hydrogum) (n = 10) e de alta estabilidade (Hydrogum 5) (n = 10), sendo produzidos com o auxílio de um bloco metálico cilíndrico e um molde metálico em forma de anel (especificações 18, 19 e 25, ANSI/ADA). Para o teste de estabilidade dimensional, dez imagens foram obtidas imediatamente e para cada tempo de armazenamento (15 min, 24, 48, 72, 96 e 120 horas), realizadas por câmera digital. As amostras foram mantidas hermeticamente fechadas em sacos plásticos (23°C). Para o teste de reprodução de detalhes, as amostras foram utilizadas para obter 140 (n = 70 por grupo) modelos de gesso, sendo observada a precisão angular de três sulcos (20 µm, 50 µm e 75 µm) para cada período. A precisão da reprodução de detalhes foi classificada usando uma classificação de pontuação predeterminada. As medições das mudanças dimensionais foram feitas no programa Corel DRAW X6. Os dados foram submetidos ao teste t de Student (α = 0,05). Resultados: Foi observada diferença estatística em relação à matriz após 24h para ambos os alginatos. Uma mudança dimensional linear negativa estatisticamente significativa (contração) foi verificada após 24 h de armazenamento (1,52% para alginato de alta estabilidade; 1,32% para alginato convencional). O alginato de alta estabilidade manteve os detalhes completos por até 72 horas, enquanto o alginato convencional, por 24 horas. Os alginatos reproduziram o sulco de 75 µm para todos os períodos. Conclusão: As impressões feitas com ambos os alginatos devem ser imediatamente vazadas para se ter resultados clínicos satisfatórios.

Evaluación de la precisión de impresiones sobre implantes usando guía multifuncional en el sistema all-on-four / Accuracy of implant impression using a multifunctional guide in the All-on-Four treatment concept

ABSTRACT Introduction: The passivity of prosthetic components is one of the most important prerequisites in oral implant rehabilitation for maintenance of osseointegration. Objective: Thus, the present study analyzed in vitro the accuracy of different molding techniques in prosthetic rehabilitation on angled implants installed in an anatomical model of a metallic edentulous maxilla. Methods: Laboratory experiment study. A reference metal model of an edentulous maxilla was used. A metal framework was used for the misadaptation assessment. Three groups (n= 10) were compared and impressions were made with vinyl-polysiloxane and casts were obtained with type IV stone: (1) Impression with a metallic open-tray without splinted transfers; (2) Impression with a metallic open-tray and metal splinted transfers; (3) Impression with a multifunctional guide and metal splinted transfers. Misadaptation was assessed with the aid of a stereomicroscope and measuring software. Data were submitted to ANOVA with Welch correction and the Games-Howell post-hoc test with the significance set at 5 percent. Results: Misadaptation (µm) was 110,23 ± 30,94, 37,53 ± 3,92, and 37,69 ± 2,79 for the the groups. Statistically significant differences between impression with a metallic open-tray with and without splinted transfers were observed (p < 0,001). No significant differences between the other types of impression. Conclusions: Impression with a metallic open-tray without splinted transfers and with a multifunctional guide splinted with metal transfers were the most precise methods resulting in higher accuracy in transferred implants(AU)

RESUMEN Introducción: La pasividad de los componentes protésicos es uno de los prerrequisitos más importantes para el mantenimiento de la osteointegración en la rehabilitación oral sobre implantes. Objetivo: Evaluar in vitro la precisión de diferentes técnicas de impresión en rehabilitación sobre implantes inclinados instalados en un modelo anatómico de un maxilar metálico desdentado. Métodos: Estudio de laboratorio de tipo experimental. Se utilizó un modelo metálico de referencia de un maxilar desdentado. Fue utilizada una barra metálica para la evaluación de la desadaptación. Se compararon tres grupos (n = 10), se realizaron impresiones con polivinilsiloxano y se obtuvieron modelos con yeso piedra tipo IV: (1) impresión con una cubeta metálica abierta sin unión de los transferentes; (2) impresión con una cubeta metálica abierta y unión de los transferentes con cilindros metálicos; (3) impresión con una guía multifuncional y unión de los transferentes con cilindros metálicos. La desadaptación se evaluó con la ayuda de un microscopio estereoscópico y un software de medición. Los datos se enviaron a ANOVA con la corrección de Welch y la prueba post-hoc de Games-Howell con la significación establecida en 5 por ciento. Resultados: La desadaptación (µm) fue de 110,23 ± 30,94; 37,53 ± 3,92 y 37,69 ± 2,79 para los grupos, respectivamente. Se observaron diferencias estadísticamente significativas entre la impresión con cubeta abierta metálica con y sin unión de los transferentes (p <0,001). No hubo diferencias significativas entre los otros tipos de impresiones. Conclusiones: La impresión con cubeta abierta metálica sin unión de los transferentes y con una guía multifuncional con unión de los transferentes con cilindros metálicos fueron los métodos más precisos que dieron como resultado una mayor precisión en la transferencia de la posición de los implantes(AU)

Dimensional stability of alginate molds scanned at different storage times / Estabilidade dimensional de moldes de alginato digitalizados em diferentes tempos de armazenamento

ABSTRACT The aim of this study was to evaluate the precision and accuracy of molds made with four commercial brands of alginate scanned at different times using digital model analysis. Eighty molds of a standard Typodont were made using 4 types of alginate (CCC: Cavex Color Change; IA: Identic Alginate; HY5: Hydrogum 5 and JP: Jeltrate Plus). The molds were scanned at four times: immediately (T1), 24h (T2), 72h (T3) and 120h (T4) after molding. Measurements were taken in three dimensions: anteroposterior, transverse and vertical. Significant differences in dimensional changes were noted between the materials over time (p <0.05). Anteroposterior dimensional variation was noted between times, especially for IA and JP. For transverse and vertical variables, a difference was found between the groups, especially at 24 h, 72 h and 120 h. CCC presented significant dimensional shrinkage only at T120 (transverse). IA and JP presented larger dimensional distortions in the vertical measurements. The molding materials used were not dimensionally stable when evaluated after 120 hours of molding. However, such evidence suggests that alginates with longer storage time, such as Cavex Color Change, are more accurate than conventional alginates.

RESUMO O objetivo do presente estudo foi avaliar a precisao e acurácia por meio de análise de modelos digitais de moldes digitalizados obtidos com quatro marcas comerciais de alginato em diferentes tempos. Oitenta moldes de um Typodont padrao foram obtidos utilizando 4 tipos de alginato (CCC: Cavex Color Change; IA: Identic Alginate; HY5: Hydrogum 5 e JP: Jeltrate Plus). Os moldes foram escaneados em quatro tempos: mediatamente (T1), 24h (T2), 72h (T3) e 120h (T4) após a moldagem. As medidas foram feitas em très dimensoes: ântero-posterior, transversal e vertical. Diferenças significativas nas mudanças dimensionais foram observadas entre os materiais ao longo do tempo (p <0,05). Variação dimensional ântero-posterior foi observada entre os tempos, principalmente para IA e JP. Para as variáveis transversal e vertical houve diferenga entre os grupos, principalmente em 24h, 72h e 120h. CCC apresentou contração dimensional significativa apenas em T120 (transversal). IA e JP apresentaram maiores distorções dimensionais na vertical. Os materiais de moldagem utilizados nao foram dimensionalmente estáveis quando avaliados após 120 horas de moldagem. No entanto, tais evidencias sugerem que os alginatos com maior tempo de armazenamento, como Cavex Color Change, sao mais precisos do que os alginatos convencionais.

Evaluating the effect of different combination of impression and pouring materials on marginal and internal adaptation of zirconia crowns / Evaluación del efecto de diferentes combinaciones de materiales de impresión y vertido en la adaptación marginal e interna de las coronas de circonio

Purpose: Two important factors in dental prosthesis are making an accurate impression and producing a suitable cast which represents the exact relationship between prepared tooth and oral structures. This study, aimed to investigate the effects of different combinations of impression and pouring materials on marginal and internal adaptation of premolar zirconia crowns. Material and Methods: Forty maxillary premolars were prepared considering round shoulder finish line. The impressions were made either by additional (Panasil) or condensation (Speedex) silicon, and poured by two different types of gypsum materials (Siladent or GC gypsum) (N=10). Zirconia crowns were fabricated using a CAD-CAM system. The crowns were cemented, and the samples were cut in bucco-lingual direction. Marginal and internal gaps were measured by stereomicroscope (×25). Results: The mean marginal gaps for Pansil-Siladent, Panasil-GC, Speedex-Siladent, and Speedex-GC were 141 µm, 143 µm, 131 µm, and 137 µm respectively. The internal gaps were 334 µm, 292 µm, 278 µm, and 257 µm respectively. The independent T-Student test showed no significant differences in average marginal or internal gap among various impression and gypsum materials or their interactions (p>0.05). Two-way ANOVA test showed no significant differences in maximum marginal or internal gap among various impression and gypsum materials and their interactions (p>0.05). Conclusion: The present study revealed no statistically significant difference in marginal/internal gap among crowns prepared using different combinations of impression-pouring materials evaluated.

Introducción: Dos factores importantes en la prótesis dental son hacer una impresión precisa y la producción de un modelo adecuado que represente la relación exacta entre el diente preparado y las estructuras orales. Este estudio, tuvo como objetivo investigar los efectos de diferentes combinaciones de materiales de impresión y vertido sobre la adaptación marginal e interna de coronas de zirconio premolar. Material y Métodos: Se prepararon cuarenta premolares maxilares considerando la línea de meta del hombro redondo. Las impresiones se realizaron con silicio adicional (Panasil) o de condensación (Speedex) y se vertieron con dos tipos diferentes de materiales de yeso (yeso Siladent o GC) (N = 10). Las coronas de zirconio se fabricaron utilizando el sistema CAD-CAM. Las coronas se cementaron y las muestras se cortaron en dirección buco-lingual. La brecha marginal e interna se midió con estereomicroscopio (×25). Resultados: Las brechas marginales medias para Pansil-Siladent, Panasil-GC, Speedex-Siladent y Speedex-GC fueron de 141µm, 143µm, 131µm y 137µm, respectivamente. Las brechas internas fueron 334µm, 292µm, 278µm y 257µm, respectivamente. La prueba de T-Student independiente no mostró diferencias significativas en la brecha marginal o interna promedio entre varios materiales de impresión y yeso o sus interacciones (p>0.05). La prueba ANOVA bidireccional no mostró diferencias significativas en el espacio marginal o interno máximo entre varios materiales de yeso y de impresión y sus interacciones (p>0.05). Conclusión: El presente estudio no reveló diferencias estadísticamente significativas en la brecha marginal/interna entre las coronas preparadas con diferentes combinaciones de materiales de impresión y vertido evaluados.

In vitro evaluation of the application of digital individual tooth tray in the impression making of mandibular full-arch crown abutments / 北京大学学报(医学版)

OBJECTIVE@#To establish a method for the production of digital individual tooth tray based on three-dimensional (3D) scan, computer-aided design (CAD) and 3D printing, and to evaluate the effect of impression taking of full-arch crown abutments by digital individual tooth tray technique and conventional method through in vitro study.@*METHODS@#The full crown preparation was performed on all the fourteen resin teeth in a standard model of mandibular dentition. The surface data of prepared abutments was collected by 3D scanning. A new project was created in a dental CAD software including all the fourteen teeth in the mandibular dentition. The design modules of anatomy crown and coping were selected for each tooth. The dentition was divided for three sections: right posterior teeth, anterior teeth, and left posterior teeth areas. The connector design was added between the abutments within the same section. The scanned data of the abutments were imported. The occlusal plane and insertion path were determined. The position of margin line, as well as the shape of anatomy crown and connector as the main body of the individual tooth tray were designed for each abutment. The shape of coping was generated as the space for holding the impression material. The finalized data of the main body was imported into Geomagic software. The retentive attachment was added at the external surface and the tissue stop was formed at the internal surface. The completed individual tooth tray was manufactured by 3D printing with resin material. The data of full-arch crown abutments were modified and printed. The conventional dentition trays A and B, as well as digital individual tooth tray were designed and printed for four copies each. The polyether impressions of the full-arch abutments were made by conventional one-step method using dentition tray A, and by sectional-impression technique using digital individual tooth tray and dentition tray B for four times each. The time spent for each impression taking and the numbers of defects at the shoulder and axial/occlusal surface in each impression were recorded. The impression quality of each abutment was evaluated. The overall quality distribution and the pass rate of abutments between the two methods were analyzed.@*RESULTS@#The impressions made by conventional method had more defects at shoulder than those made by digital individual tooth tray technique. No difference of the number of defects at axial/occlusal surface between the two methods was observed. The digital individual tooth tray technique for the full-arch abutment impression exhibited higher pass rate of abutments and better quality of impression, compared with conventional methods.@*CONCLUSION@#A new method for the production of digital individual tooth tray based on digital scanning, CAD and 3D printing was established. Compared with conventional method, using digital individual tooth tray technique for impression taking of full-arch abutments can achieve better effect.

Effect of disinfectant with benzethon chloramine and isopropanol as main active ingredients on the accuracy of dental impression / 北京大学学报(医学版)

OBJECTIVE@#To assess the effect of disinfectant (Cavicide) with benzethon chloramine and isopropanol as main active ingredients disinfectant on dental impression accuracy.@*METHODS@#The effect of Cavicide on three impression materials (alginate, polyether and vinylpolysiloxane) were assessed using a standard model. The standard model was digitized by an extraoral scanner (IScan D103i, Imetric). For each kind of impression materials, thirty impressions were taken following the manufactures' instruction in the same conditions. Subsequently, the impressions were randomly divided into three groups, with ten impressions in each group. After the impression taking was completed, the three groups underwent pure water rinse for 1 min (blank control, BC), 2% glutaraldehyde solution immersion disinfection for 30 min (glutaraldehyde, GD), and Cavicide solution spray disinfection for 5 min (Cavicide, CC), respectively. All the impressions were digitized by the extraoral scanner (IScan D103i, Imetric) after disinfection and exported to a dedicated three-dimensional analysis software (Geomagic Qualify 2014, Geomagic, USA). In the software, the digital models of the impressions were trimmed to teeth and then superimposed with the digitized standard model via best-fit alignment. Root mean square (RMS) was used to evaluate the deviations between the impression and the standard model. The deviation in the anterior and posterior regions was evaluated respectively. One-way ANOVA test and the LSD post-hoc test were used to compare the deviations between the three groups (P < 0.05). The color map of each superimposition was saved for visual analysis.@*RESULTS@#For the polyether and vinylpolysiloxane materials, the difference between the three groups was not statistically significant (P=0.933, P=0.827). For the alginate material, the difference in posterior region between group GD and group BC, as well as group GD and group CC were statistically significant (GD vs. BC, P=0.001; GD vs. CC, P=0.002), while the difference between group BC and group CC was not statistically significant (P=0.854). The visual analysis showed an obvious deviation in the buccal-lingual direction in group GD.@*CONCLUSION@#Disinfectant (Cavicide) with benzethon chloramine and isopropanol as main active ingredients using spray disinfection has no effect on the accuracy of the alginate, polyether and vinylpolysiloxane impressions.

Dimensional Stability of Casts Derived from Three Types of Alginate at Different Times After Impression

Objective: To evaluate the dimensional changes in three types of alginate following three different delay times after casting. Material and Methods: In this laboratory study, a maxillary arch-shaped stainless steel model was prepared and three pins with similar and determined diameters and heights were placed (one at mid-line and two on the underside of the model) as reference points to compare the dimensional stability of the three types of alginates. A special metal tray was made from the main model. The main moldel was imprisoned by the metal tray, and these were kept for a specific time in a humid environment. Gypsum Type 4 was poured over the impression to obtain 90 gypsum casts for three types of alginate. The dimensions of casts obtained from each alginate were compared in two lateral and anterior-posterior dimensions, they were compared with each other, and the alginates were also compared to the main model. Results: At a time interval of 15 minutes, the dimensional accuracy of the casts obtained from the three types of alginates, with the main model in both anterior-posterior and transverse dimensions was not significantly different (p<0.05); but there was a significant difference at 60 minutes and 24 hours in both dimensions (p<0.05). Although there was no significant difference between the alginates in both dimensions and all three studied time periods, the least difference with the main model was related to Zhermack and the highest difference was related to Golchai alginates. Pairwise comparisons showed that none of the samples had a significant difference in terms of dimensions. Conclusion: The dimensional stability of alginate was a time-dependent type of alginate and had no significant effect on the dimensional accuracy of casts.

Injection Shrinkage аnd Water Sorption of Some Thermoplastic Dental Materials

Objective: To evaluate the change of diameter of different injection-molded thermoplastic materials. Material and Methods: Four thermoplastic injection-molded materials were analyzed (Bre.flex 2nd edition, Vertex ThermoSens, Perflex Biosens and Polyan IC). A total of 432 test samples were made in the form of an "hourglass". All samples were divided into three groups: Group I (Control) - consisting of 36 test samples for each type of material, that was not exposed to artificial aging or a wet environment; Group II - consisting of 36 test samples for each type of material, that were artificially aged through dehydration; Group III - specimen were subjected to artificial aging without dehydration. The diameter of each specimen was measured with a digital caliper. Data were analysed using the Student's t-test. Results: Regarding to shrinkage, the samples from the Bf Control group have a mean value of 1.56 mm and was observed a shrinkage of the injection-molded polyamide material within 0.25%. The comparison between the samples from Group II and Group III showed statistically significant differences (p<0.001). There were no significant differences between groups for Thermosens and Biosens (p>0.05). The comparison between Group II and Group III for Polyan IC samples shows that Group III has a higher arithmetic mean value (p<0.01). Conclusion: Shrinkage of the polymers during the injection process is present in all materials. The thermocycling and the storage in a dry or in a wet environment of the samples results in a change of the diameter in almost every single type of material.

Marginal adaptation of provisional crowns made of acrylic and bisacrylic resins using different impression materials

Aim: To evaluate the marginal adaptation of provisional crowns made of acrylic and bisacrylic resins using different impression materials. Methods: a metal die and a matrix applied through a direct technique were used to fabricate the specimens. The impression materials used as a matrix were divided into four groups: Irreversible hydrocolloid(IH), laboratory silicone (LS), condensation silicone (CS), and addition silicone (AS). After the impression procedures, each matrix was loaded with the provisional prosthetic materials, Alike, Duralay, Protemp 4, and Structur 3 (n = 12). Marginal discrepancy was evaluated using a stereomicroscope at ×45 magnification. The images obtained were transferred to the Corel Draw X7 program, and the distances from the cervical margins of the specimen to the reference lines at the metal die were measured vertically. The data were analyzed by using 2-way ANOVA followed by the Tukey test (α=.05). Results: the acrylic resins had higher values ​​of marginal discrepancy compared to the bisacrylic resins. A statistically significant difference was found between all impression materials, and the irreversible hydrocolloid presented higher values of discrepancy (303.28­613.31 µm), whereas addition silicone had the lowest (48.61­190.06 µm). Conclusions: the bisacrylic resins had a better marginal adaptation compared to the acrylic resins. The addition silicone promoted a better marginal adaptation of the provisional prosthetic materials tested, followed by condensation silicone, laboratory silicone, and irreversible hydrocolloid

Comparison of impression techniques and double pouring by dental cast's accuracy. Preliminary clinical-lab trial

Aim: This study compared impression techniques and double pouring by means of cast's accuracy. Methods: For each patient (n=10), impressions from right maxillary canine to first molar were made with acrylic resin trays and vinyl-polysiloxane using one single-step, and four two-steps techniques: relief with poly(vinyl chloride) film; tungsten-carbide bur/scalpel blade; small movements of the tray; non-relief. Total visible buccal surface area of crowns was measured three times using photographs from patients (Baseline) and casts. Mean area values (mm2) between Baseline and casts differences were analyzed by two-way repeated-measures ANOVA (α=.05; 1-ß=85%). Results: No significant differences were observed for Impression Techniques (P=.525), Double Pouring (P=.281), and their interaction (P=.809). Conclusion: All impression techniques and double pouring produced casts with similar accuracy

Estabilidade dimensional de moldes obtidos com alginato de armazenamento tardio / Dimensional stability of molds obtained with late storage alginate

Resumo Introdução Recentemente, vêm surgindo no mercado alguns alginatos de armazenamento prolongado. Não há, no entanto, um consenso na literatura a respeito da estabilidade dimensional destes materiais durante este armazenamento Objetivo Avaliar, por meio de método prático experimental, a estabilidade dimensional de um alginato de armazenamento tardio. Material e método O material de moldagem utilizado foi o alginato Hydrogum 5 (Zhermack). Uma matriz metálica cilíndrica foi utilizada para a realização das moldagens, com 38 mm de diâmetro externo, 30 mm de diâmetro interno e cuja superfície superior apresenta três linhas paralelas entre si com 25 mm de comprimento e 20, 50 e 75 µm de largura. Após o tempo de geleificação do material de moldagem, 16 moldes foram colocados em um umidificador e essas amostras foram fotografadas utilizando-se uma câmera digital (Canon EOS Rebel 3Ti, Canon) associada a um software para análise das imagens obtidas (ImageJ 1.52a, U.S. National Institutes of Health; DI). A calibragem da régua foi 10 cm e, posteriormente, três linhas foram medidas três vezes, para se obter uma média dos comprimentos das linhas. As amostras foram fotografadas nos seguintes intervalos: imediatamente, 24, 48, 72, 96 e 120 horas. Resultado Os dados mostraram diferenças estatisticamente significantes para o fator tempo quando comparada a leitura imediata com os demais períodos de tempo de leitura (p<0,001) e quando comparada a leitura após 24 h de armazenagem com os demais períodos de tempo (p<0,001). Não houve diferença estatística (p>0,05) quando os tempos de armazenamento de 48 h, 72 h, 96 h e 120 h foram comparados entre si. Todos os valores encontravam-se dentro dos valores preconizados pela ISO 21563:2013. Conclusão Os moldes dos alginatos testados podem ser armazenados por até cinco dias em 100% de umidade relativa.

Abstract Introduction Recently, some extended-pour alginate impression materials have been placed in the market. However, there is no consensus in the literature regarding the dimensional stability of these materials during these storage. Objective To evaluate, through the experimental model, the durability and velocity with respect to dimensional alteration, analyzing the material and detecting distortions. Material and method The material for molding in this test was alginate (Hydrogum 5, Zhermack). A cylindrical metallic matrix was used to make the moldings with: 38 mm of external diameter, 30 mm of internal diameter and superior of the upper series of the card 3d transport lines with each 25 mm in length and 20, 50 and 75μm in width. After the time of jellification / polymerization of the molding material, 16 molds were inserted in a doser and were photographed with a digital camera (Canon EOS Rebel 3Ti, Canon) associated with a software for analysis of sacred images (ImageJ 1.52a, US National Institutes of Health, DI). The calibration of the ruler was performed in 10 cm and then in 3 lines were means 3 (three) times to obtain a mean of the lengths of the lines. The photographs were taken at the following intervals: immediately, 24, 48, 72, 96 and 120 hours after being cast. Result The data were found when compared with the other parts of the reading time (p <0.001) and when compared to the execution after 24 hours of locomotion with the other parts of the time (p <0.001). The rest time of 48 hours, 72 hours, 96 hours and 120 hours were compared to each other. Conclusion The molds of the tested alginates can be stored for 5 days in 100% relative sauce.

Avaliação da estabilidade dimensional da silicona de condensação em diferentes tempos de vazamento em moldagens para prótese fixa / Evaluation of the dimensional stability of the condensation silico-ne in different leakage times in moldings for fixed prosthesis

Introdução: O envelhecimento da população aumenta a necessidade de reabilitação protética e o custo do atendimento odontológico. Para reabilitar com qualidade e baixo custo é necessário conhecer os materiais odontológicos desse processo, como os materiais de moldagem. O mais utilizado no Brasil é a silicona de condensação, que possui limitações. Porém, o fabricante modificou a fórmula com o intuito de melhorar a estabilidade dimensional. Objetivo: avaliar a estabilidade dimensional da silicona de condensação Speedex com a nova tecnologia DCP, em diferentes tempos de vazamento nas moldagens para prótese fixa. Material e métodos: Foi confeccionado um modelo padrão metálico com dois cilindros de mesmos diâmetros e mesma altura para simular uma prótese fixa. Foi elaborada uma moldeira metálica padronizada com retenções e guias de inserção. A partir dessa, outras quatro, em acrílico incolor, foram reproduzidas pelo alginato reversível. No total, foram realizadas 20 impressões, sendo 5 impressões por grupo. Os grupos foram vazados com o gesso tipo IV em diferentes tempos: grupo 1 (n=5): imediato; grupo 2 (n=5): 30 min; grupo 3 (n=5): 36h; grupo 4 (n=5): 72h. O modelo padrão e todos os modelos de gesso do grupo 1, 2, 3 e 4 foram medidos por dois pesquisadores de forma cega com auxílio de um paquímetro digital. Foram analisadas as distâncias externas e internas entre os pontos de referência dos cilindros. Os grupos foram comparados pelo teste t de Student, o nível de significância considerado foi p<0,05. Resultados: não se observou diferença estatística entre as medidas do pesquisador 1 e 2 (p>0,05). Não houveram diferenças entre os grupos 1 e 2 e 1 e 3; porém houve diferença significativa entre o 1 e 4. Conclusão: A silicona de condensação Speedex, não altera a estabilidade dimensional com o vazamento em até 36 horas.

Introduction: The aging of the population increases the need for prosthetic rehabilitation and the cost of dental care. To rehabilitate with quality and low cost is necessary to know the dental materials of this process, such as impression materials. The most used in Brazil is condensation silicon, which has limitations. However, the manufacturer modified the formula to improve dimensional stability. Objective: To evaluate the dimensional stability of Speedex condensation silicon with the new DCP technology at different casting times in fixed prosthesis moldings. Material and methods: A standard metal model with two cylinders of the same diameters and the same height was made to simulate a fixed prosthesis. A standard metal tray with drawers and insertion guides was developed. This metal tray was duplicated using reversible alginate. From this, four colorless acrylic trays were reproduced. In total, 20 impressions were made, with 5 impressions per group. The groups were cast with type IV gypsum at different times: group 1 (n=5): immediate; Group 2 (n=5): 30 min; group 3 (n=5): 36h; group 4 (n=5): 72h. The standard model and all gypsum models of groups 1, 2, 3 and 4 were measured by two researchers blindly using a digital caliper. The external and internal distances between the reference points of the cylinders were analyzed. The groups were compared by Student's t test, the significance level considered was p<0.05. Results: no statistically significant difference was found between researcher 1 and 2 by (p<0.05). There were no differences between groups 1 and 2 and 1 and 3; however, there was a significant difference between 1 and 4. Conclusion: Speedex condensing silicone does not change dimensional stability with leakage within 36 hours. Key-words: Dental Impression Materials, Dental Prosthesis, Silicone Elastomers. Submetido: 14/06/2019Aceito: 16/08/2019 Rebeca Vidal Capelupi1,2,Viviam Salvato de Souza1,2,Marcelo Tarcísio Martins1,Júlio Marcos Gouvêa Chagas1,Rogério Teodoro de Aquino3,Thalyta dos Reis Furlani Zouain-Ferreira1,Fabiana Aparecida Mayrink de Oliveira1,21Faculdade de Ciências Médicas e da Saúde de Juiz de Fora, Curso de Odontologia ­ Juiz de Fora, MG. 2Programa Institucional de Bolsas de Iniciação Científica (PIBIC) ­ FCMS/JF 2018.2 3Usinagem Mecânica Industrial, SENAI, Juiz de Fora, MG. Avaliação da estabilidade dimensional da silicona de condensação em diferentes tempos de vazamento em moldagens para prótese fixaEvaluation of the dimensional stability of the condensation silico-ne in different leakage times in moldings for fixed prosthesis * Fabiana de OliveiraAvenida Barão do Rio Branco, 1871/1105, CentroJuiz de Fora ­ MG CEP: 36013-020 8 fabsmay@hotmail.com

Effect of techniques, trays and materials on accuracy of impressions clinically made / Efeito de técnicas, moldeiras e materiais na exatidão de moldagens odontológicas

Abstract Introduction Making accurate and dimensionally stable impressions to duplicate oral conditions and tooth morphology is an essential step of prosthetic dentistry for fabricating well-fitted indirect restorations and, consequently, ensure the longevity and success of the treatment. Several authors describe pros and cons of different impression techniques, although there is no unanimity among them about the best one. Objective This study evaluated casts' accuracy made by different impression techniques, trays and materials. Material and method 10 patients were selected and 20 impressions from teeth #13 to #16 were performed using single-step (SS) and two-step techniques, made with metal stock and customized acrylic resin partial trays, vinyl polysiloxane and condensation silicone rubbers. Type IV gypsum was used to pour the casts. Three photographs of each patient (baseline), as their respective gypsum casts, were taken, measured in their interested buccal surface area. Comparisons of area values among experimental groups and baseline were performed. Data showed adherence to normal curve, being submitted to 3-way ANOVA/Bonferroni test (α=.05). Result Technique produced significant differences (P=0.02). SS technique was more accurate than BUR one (P=0.003; 95=1.22 to 5.98), but both resulted in similar casts to PVC, MOV and NR techniques, which were similar to each other (P>0.05). Conclusion SS technique showed the closest absolute values to baseline.

Resumo Introdução Realizar moldagens precisas e dimensionalmente estáveis que dupliquem a condição oral é um passo essencial para a confecção de restaurações indiretas de qualidade, garantindo seu sucesso e longevidade. Diversos estudos tem demonstrado os prós e contras de diferentes técnicas de moldagem, mas nenhum consenso da melhor técnica ainda foi descrito. Objetivo Este estudo avaliou a exatidão de modelos de gesso confeccionados por diferentes técnicas de moldagem, moldeiras e materiais. Material e método 10 pacientes foram selecionados e 20 moldes dos dentes #13 até #16 foram realizados utilizando técnicas simultânea (SS) e de dois passos, realizados com moldeiras parciais metálicas e individuais de resina acrílica, silicones de adição e condensação. Gesso tipo IV foi usados para os vazamentos. Três fotografias de cada paciente (baseline), assim como dos seus respectivos modelos de gesso foram realizadas e sua área foi então mensurada, na porção vestibular. Comparações de valores de área entre os grupos experimentais e o baseline foram performadas. Os dados mostraram aderência a curva normal, sendo submetidos ao teste 3-way ANOVA/Bonferroni (α=.05). Resultado As técnicas produziram diferenças significativas (P=0.02).Técnica simultânea foi mais precisa que a BUR (P=0.0003; 95=1,22 a 5.98), mas ambas resultaram em modelos similares àqueles feitos por meio das técnicas de PVC, MOV e sem NR, que foram similares entre si (P>0.05). Conclusão Técnica simultânea demonstrou valores absolutos similares àqueles demonstrados pelo baseline.

Establishment and preliminary clinical evaluation of edentulous custom trays designed and fabricated by chair-side CAD and 3D printing systems / 北京大学学报(医学版)

OBJECTIVE@#To design and fabricate edentulous custom trays by chair-side computer-aided design and 3-dimensional printing (CAD/3DP) system of independent research and development and to evaluate their clinical effects based on prosthodontists'satisfaction using the visual analogue scale (VAS).@*METHODS@#Fifteen edentulous patients were randomly recruited by three prosthodontists who passed the unified operating process training. The custom trays for each patient were fabricated using both chair-side CAD/3DP system of independent development and manually conventional method, and the final impressions were made by silicone impression materials (light body). The prosthodontist's satisfaction was surveyed by the three prosthodontists via the questionnaire based on visual analogue scales.@*RESULTS@#In the degree of the prosthodontist's satisfaction of final impressions, the average satisfactions of "try in" (the overall size, shape, convenience, etc.) on the 3DP custom tray made by independent development chair-side system and the manually conventional method were 9.18±0.19 and 8.23±0.22, respectively. The average satisfactions of the border line position (border extensions, frenal notch)were 8.91±0.40 and 7.96±0.23, respectively. The average satisfactions of the stability in border molding were 8.80±0.83 and 8.01±0.81, respectively. The average satisfactions of the quality of final impression (completeness, thickness of impression material, exposure of custom tray, shape of border) were 8.94±0.68 and 7.99±0.42, respectively. The average satisfactions of the difficulty of high quality impression (times of repetition, efficiency) were 9.20±0.37 and 7.88±0.22, respectively. The average satisfactions of the overall satisfaction were 9.11±0.49 and 7.95±0.15, respectively. There was significant difference in the satisfaction of "try in", border line position, stability in border molding, quality of final impression, difficulty of high quality impression, and overall satisfaction between the 3DP custom tray made by chair-side system of independent development and the manually conventional method (P<0.05).@*CONCLUSION@#In the degree of the prosthodontist's satisfaction of final impression, the 3DP custom tray made by chair-side system of independent development is higher than that of the conventional custom tray, and it meets the clinical requirements and can be popularized in clinical application.

Evaluation of the Accuracy of Conventional and Digital Methods of Obtaining Dental Impressions / Evaluación de la Exactitud de los Métodos Convencionales y Digitales de la Obtención de Impresiones Dentales

ABSTRACT: The aim of this study was to carry out a literature review on the accuracy of conventional and digital dental impression methods, as well as present the various three-dimensional intraoral scanning systems. A bibliographic search was carried out in PUBMED's main health database, in which works published between 2008 and 2018 were collected. Laboratory studies, case reports and systematic reviews were included, addressing topics that deal with conventional digital materials, impression and precision. Articles that did not evaluate impression materials, their behavior and techniques to obtain a good impression of oral structures were excluded. Through a review in the literature, obtained the following findings: the most critical stage in macking a dental prothesis is to take the dental impression. The conventional technique of impression consists of obtaining a negative copy of the intra-oral situation that will be poured into gypsum, obtaining a positive copy, on which the work will be carried out. Digital scanning systems were not superior to conventional moldings when comparing fidelity, accuracy and detail reproduction; in contrast, they were superior to conventional impression when considering clinical chair time, patient and operator preference, and patient comfort.

RESUMEN: El objetivo de este estudio consistió en realizar una revisión bibliográfica sobre la precisión de los métodos de moldeo dental convencionales y digitales, así como presentar los diversos sistemas de escaneo intraoral tridimensionales. Se realizó una búsqueda bibliográfica en la base de datos de salud principal de PUBMED en la cual se recopilaron trabajos publicados entre 2008 y 2018. Se incluyeron estudios de laboratorio, informes de casos y revisiones sistemáticas, abordando temas que tratan con materiales digitales convencionales, moldeo y precisión. Se excluyeron los artículos que no evaluaron los materiales de moldeo, su comportamiento y técnicas para obtener una buena impresión de las estructuras orales. A través de una revisión exhaustiva en la literatura, obtuvimos los siguientes hallazgos: el paso más crítico en la preparación de una pieza protésica es la impresión de la preparación. La técnica convencional de moldeo consiste en obtener una copia negativa de la situación intraoral que se verterá en el yeso, obteniendo una copia positiva, sobre la cual se realizará el trabajo. Resulta que los sistemas de escaneo digital no fueron superiores a las molduras convencionales al comparar la fidelidad, precisión y reproducción de detalles; en cambio, fueron superiores a las molduras convencionales al considerar el tiempo de trabajo clínico, la preferencia del paciente y del operador y la comodidad del paciente.

Estudio comparativo de tres materiales de impresión en su capacidad para reproducir el margen cervical de la preparación mediante las técnicas de doble hilo y cofia de trasferencia / Comparative study of three impression materials in their capacity to reproduce the cervical margin of preparation using techniques of coping and double cord

En prótesis fija la integridad marginal o perfección del margen es de suma importancia así como una impresión que copie perfectamente el terminado de la preparación ya que de esto depende la adaptabilidade de la prótesis que permita la supervivencia de la restauración y el mantenimiento de la salud periodontal en la boca del paciente. En este estudio se compara la capacidad de tres materiales de impresión (2 siliconas por adición y 1 poliéter) para copiar el margen cervical de la preparación mediante las técnicas de doble hilo y cofia de trasferencia. Se utilizaron 96 primeros molares inferiores izquierdos divididos en 6 grupos de 16 c/u se restauraron los dientes con ionómero de vidrio, resina o poste colado según fuera el caso, se prepararon los dientes con terminación en chamfer, el grupo 1: técnica de doble hilo con silicone por adición (Silicona 1), grupo 2: técnica de doble hilo con poliéter, grupo 3: técnica de cofia de transferência con silicona (Silicona 1), grupo 4: técnica de cofia de transferencia con poliéter, grupo 5: Técnica de doble hilo con silicona (Silicona 2), grupo 6: Técnica de cofia con silicona (Silicona 2). Posteriormente fueron observados en el estereomicroscopio para evaluar la cantidad de burbujas e irregularidades en el margen cervical según la escala de Jokstad. Donde la prueba estadística de Chi-cuadrada con un nivel de confianza de < 0.05 no mostró diferencia estadística significativa entre las técnicas de impresión de doble hilo y la de cofia de trasferencia, independientemente del material usado. Aunque numéricamente la técnica de doble hilo se comportó mejor que la técnica de cofia por lo que se sugiere su uso.

In fixed prosthesis, the integrity of perfection of the margin is of utmost importance, as well as an impression that perfectly copies the finish of the preparations, since the adaptability of the prosthesis that ensures survival of the restoration and periodontal health depends on this. This study compares the capacity of 3 different materials (2 silicones addition and 1 polyether) to copy the cervical margin of the preparation in the impression between the techniques of double cord and coping. We used 96 lower left molars divided into 6 groups of 16 each. The teeth were restored with glass ionomer, resin or cast post and core depending on the case, the margins were finished in a chamfer (group 1), double thread with addition silicone (group 2), double thread with polyether, (group 3), coping with PVS, (group 4), coping with polyether, (group5) double cord with PVS (group 6), coping With PVS. They were subsequently evaluated in a stereomicroscope to observe the number of bubbles and irregularities in the cervical margin according to the Jockstad scale, where the Chi-square test with a confidence level of <0.05 showed no statistically significant difference between impression techniques and coping regardless of material used. Although numerically the double-thread technique behaved better than coping technique, so it is suggested its use.

Avaliação da alteração dimensional de quatro marcas comerciais de silicone por reação de adição variando o tempo de armazenagem dos moldes / Dimensional alteration assessment of four silicone brands through addition reaction varying molds storage time

O objetivo deste estudo foi mensurar e comparar a precisão dimensional de modelos de gesso confeccionados por meio de moldagem de impressão única (material pesado/fluído de uma única vez) com quatro diferentes marcas comerciais de silicone polimerizados por reação de adição (Express XT®, Futura®, Aquasil® e Virtual®). Inicialmente, foi confeccionado um modelo acrílico mestre, o qual possuía três pilares metálicos paralelos entre si e equidistantes 50 mm um do outro. Para obtenção dos moldes foram utilizadas cinco moldeiras individuais em acrílico, cujas faces externas adaptavam-se perfeitamente na base do modelo padrão, promovendo o "stop" de inserção da moldeira. Após o procedimento de moldagem e confecção dos modelos experimentais, foram medidas as distâncias entre os três cilindros e o diâmetro de cada cilindro. Essas medições foram feitas por três vezes em um mesmo ponto e, destas, criou-se uma média obtendo os resultados finais. Os valores das distâncias foram analisados estatisticamente por meio de uma análise bifatorial, e as médias comparadas pelo teste de Tukey (5%). Os dados demostraram que todas as marcas analisadas apresentaram alteração dimensional e diferiram entre si quando comparadas.

The objective of this study was to measure and compare the dimensional accuracy of plaster models made by only impression molding (heavy material/fluid at one time) of four different brands of polymerized silicone through addition reaction (Express XT®, Futura ®, Aquasil® and Virtual®). Initially, a master acrylic model was manufactured, which had three parallel metal pillars and equidistant 50 mm from each other. To obtain the impressions, we used five individual acrylic trays, whose external faces perfectly adapted to the standard model base, thus promoting the "stop" of molding insertion. Following the molding procedure and the experimental models manufacturing, distances between the three cylinders and the diameter of each cylinder were measured. These measurements were made three times at the same point, and from these average results were obtained. The distance values were statistically analyzed using a two-factor analysis and the means compared by Tukey test (5%). The data demonstrated that all the analyzed brands presented dimensional changes and differed from each other when compared.

Empreinte sectorielle en occlusion

L'empreinte sectorielle en occlusion est souvent citée dans la littérature comme une méthode alternative pour réaliser des empreintes en prothèse conjointe, avec une variété de matériaux et de techniques d'empreinte. Elle présente de nombreux avantages par rapport aux techniques d'empreintes classiques. Le présent article a pour but de passer en revue les différentes indications, avantages et limites de l'empreinte sectorielle en occlusion, pour ensuite présenter la mise en oeuvre de cette technique, à travers deux cas cliniques